Open-iSCSI

This article describes how to access an iSCSI target with the Open-iSCSI initiator.

Note: iSCSI is not encrypted. Transmitting data over an unsecured channel is not recommended.

Installation

Install the open-iscsi package from the official repositories.

Note: An older initiator, Linux-iSCSI, was merged with Open-iSCSI in April 2005. This should not be confused with linux-iscsi.org, the website for the LIO target.

Overview

The following diagram shows how the Components work together. A more detailed version can be found here: Open-iSCSI modules (Outdated)

 +--------------------------------------------------------+             
 | Targets & Sessions configuration files and directories |             
 +--------------------------------------------------------+             
                                                                       
 +--------------------------+     +----------------------------------+ 
 | iscsiadm                 |     | iscsid: iSCSI daemon             | 
 |                          |     |                                  | 
 |  * Command line tool     |<--->|  * Implements Session management | 
 |  * Manages database of   |     |  * Communicates with iscsiadm    | 
 |    sessions and targets  |     |    and iscsi kernel modules      | 
 +--------------------------+     +---------------+------------------+ 
                                                  |                    
 User space                                       |                    
- - - - - - - - - - - - - - - - - - - - - - - - - | - - - - - - - - - -
 Kernel                                           v                    
         +-----------------------------------------------------------+ 
         | kernel modules: scsi_transport_iscsi, iscsi_tcp, libiscsi | 
         +-----------------------------------------------------------+

From the Open-iSCSI README:

Persistent configuration is implemented as a tree of files and directories, which are contained in two directories:

Discovery directory /etc/iscsi/send_targets which has directories named after target addresses.
Node directory /etc/iscsi/nodes which has directories named after IQN (ISCSI Unique Name) of particular device.

Configuration

Start the Service

iscsid is managed by a systemd Unit.

Start iscsid.service or iscsid.socket.

ISCSI Qualified Name (IQN)

IQN is used for identifying every device.

Open-ISCSI stores its initiator IQN in the /etc/iscsi/initiatorname.iscsi file with a format InitiatorName=iqn

During installation the initial IQN will be generated. If you wish to generate new IQN the iscsi-iname utility can be used which prints out new IQN.

Authentication

If the ISCSI target requires authentication by the initiator, the configuration file /etc/iscsi/iscsid.conf may need to be updated.

The following parameters are used for authenticating a login session of an initiator to a target:

node.session.auth.authmethod = CHAP
node.session.auth.username = initiators_username
node.session.auth.password = initiators_password

If your target has two-way authentication enabled then those lines also need to be edited:

node.session.auth.username_in = targets_username
node.session.auth.password_in = targets_password

If your target requires authentication to get the list of its nodes (most will not) then following lines should be edited:

discovery.sendtargets.auth.authmethod = CHAP
discovery.sendtargets.auth.username = initiators_username
discovery.sendtargets.auth.password = initiators_password

If your target has two-way authentication enabled then those lines also need to be edited:

discovery.sendtargets.auth.username_in = targets_username
discovery.sendtargets.auth.password_in = targets_password

Warning: No two passwords may be the same. This means that you need four unique passwords in the configuration above.

Target discovery

Request the target its nodes.

# iscsiadm --mode discovery --portal target_ip --type sendtargets

On success information about nodes and target will be saved on your initiator.

Add target manually

# iscsiadm -m node --target targetname --portal target_ip -o new

A possible scenario to use this is when server does not allow discovery.

Delete obsolete targets

# iscsiadm -m discovery -p target_ip -o delete

Login to available targets

# iscsiadm -m node -L all

or login to specific target

# iscsiadm -m node --targetname=targetname --login

logout:

# iscsiadm -m node -U all

Info

For running session

# iscsiadm -m session -P 3

The last line of the above command will show the name of the attached device e.g

Attached scsi disk sdd State: running

For the known nodes

# iscsiadm -m node

Online resize of volumes

If the iscsi blockdevice contains a partitiontable, you will not be able to do an online resize. In this case you have to unmount the filesystem and alter the size of the affected partition.

Rescan active nodes in current session
```
# iscsiadm -m node -R
```
If you use multipath, you also have to rescan multipath volume information.
```
# multipathd -k"resize map sdx"
```
Finally resize the filesystem.
```
# resize2fs /dev/sdx
```

Tips & Troubleshooting

This article or section needs language, wiki syntax or style improvements. See Help:Style for reference.

Reason: Nonstandard section, see Help:Style#Standard sections. Create proper #Tips and tricks and #Troubleshooting sections and place each issue in a separate subsection. (Discuss in Talk:Open-iSCSI)

You can also check where the attached iSCSI devices are located in the /dev tree with ls -lh /dev/disk/by-path/* .

At the server (target) you might need to include the client iqn from /etc/iscsi/initiatorname.iscsi in the acl configuration.

Many of the iscsiadm operations require that the iSCSI daemon iscsid is running. To verify that this is the case, check the status of the iscsid.service.

To run the iSCSI daemon in debug mode (make sure you stopped iscsid.service before)

# iscsid -d 8 -c /etc/iscsi/iscsid.conf -i /etc/iscsi/initiatorname.iscsi -f