SANE/Scanner-specific problems

This article contains scanner or manufacturer-specific instructions for SANE.

Agfa

Snapscan e40

Firmware Snape40.bin from here is required.

If USB autosuspend is enabled, the printer may need to be turned off and on again before each scan. USB autosuspend can be disabled using powertop.

BenQ/Acer

If you own an USB scanner from Acer (now BenQ), you need to download a suitable firmware binary and configure /etc/sane.d/snapscan.conf.

Find out which model you own and take note of the USB ID:

$ lsusb

Bus 002 Device 010: ID 04a5:20b0 Acer Peripherals Inc. (now BenQ Corp.) S2W 3300U/4300U

Go to snapscan main page and see whether your scanner is supported and which firmware you need (e.g, u176v046.bin).
Search the firmware image on the Internet and download it to /usr/share/sane/snapscan/.
Edit the head of /etc/sane.d/snapscan.conf and configure the following two lines:

firmware /usr/share/sane/snapscan/u176v046.bin
/dev/usb/scanner0 bus=usb

Brother

In order to install a Brother scanner or printer/scanner combo you need the right driver. To find the right one, see the FAQ for your model at the Brother Support, i.e. Home > Country > Your model > FAQs & Troubleshooting > Linux > Scanner / Scan Key Tool > Scan using XSane or GIMP. You can also search the web. Or see the information below for more scanners. Or extract each of the AUR packages below. Each package seems to contain an exhaustive list of the models it is suitable to.

Then, install the appropriate package:

brscan2^AUR
brscan3^AUR
brscan4^AUR (MFC-J5620DW)
brscan5^AUR
libsane-dsseries^AUR

Now, the scanner should be recognized by SANE.

For network scanners, Brother provides a different configuration tool for each brscan version (e.g., brsaneconfig2 for brscan2 compatible devices):

# brsaneconfig2 -a name=<ScannerName> model=<ScannerModel> ip=<ScannerIP>

Example:

# brsaneconfig2 -a name=SCANNER_DCP770CW model=DCP-770CW ip=192.168.0.110

To get the IP and node name of your scanner, you can use Nmap:

$ nmap -sP 10.0.0.0/24

It's also possible to add a scanner via its node name instead of its IP, for example:

# brsaneconfig4 -a name=Brother_DCP-L3550CDW model=DCP-L3550CDW nodename=BRWC0B5D72A0B87

Network Scanning

In case of network scanning, e.g. by WiFi, Sane may still be unable to find the scanner. If so, you need to specify the IP address of the scanner in the /etc/sane.d/net.conf file.

Now use scanimage --list-devices to check whether sane is able to find your scanner. If not, further check that Sane expects this device through the network (see [1]). Check that /etc/sane.d/dll.conf contains brotherX, where the X stands for the brscan version from above. If nothing was found, add brotherX to the end of the file.

Invalid argument

If all the necessary packages are installed but you still get the "invalid argument" error this could mean that the configuration file has been corrupted. Run the following command (in case of brscan4):

 # brsaneconfig4 -d

The output should narrow down the problem. Most likely the connection is not set up correctly. In case of a network scanner, check if the IP address is right by opening /etc/opt/brother/scanner/brscan4/brsanenetdevice4.cfg with an editor. In case of a USB connection, check if the path to the scanner in the configuration file is set up correctly. For that, compare the values of the lsusb command with your configuration file and change them if necessary. You might also try to follow the brotherX suggestion from Network Scanning above even for non-network scanners.

Scan-key-tool

Brother has released a tool to enable scanning to be triggered by user interaction with the scanner itself (e.g., by selecting one of "Scan to email", "Scan to image", etc. on the scanner's keypad) rather than by an attached computer. This can be set up by installing the brscan-skey^AUR package and starting brscan-skey.service using systemd. Note that by default this service runs as the brscan-skey user which is created by the package, whose home directory is located at /srv/brscan-skey.

Brother supplies some default scripts that are executed when a scan type is selected on the keypad. These may require the installation of some optional dependencies of the brscan-skey^AUR package. For all options apart from "Scan to email" the resulting output can be found inside $HOME/brscan, with $HOME the home directory of the user running this tool (so /srv/brscan-skey if started via systemd as a systemwide process).

It is possible to change what action takes place when a given type of scan is selected on the keypad. This is done by editing /opt/brother/scanner/brscan-skey/brscan-skey-0.2.4-0.cfg. For each variable SCAN_COMMAND in IMAGE, OCR, EMAIL, FILE, the command

 $ $SCAN_COMMAND $SCANNER_DEVICE $SCANNER_FRIENDLY_NAME

is executed when the corresponding scan type is selected. Note that $SCAN_COMMAND is not quoted so may specify more than one positional parameter in the final command that is executed. $SCANNER_DEVICE refers to the name of the device that should be specified to a sane frontend (e.g. via the --device-name flag when using scanimage), for example brother3:bus4;dev2. $SCANNER_FRIENDLY_NAME is the human-readable name of the scanner.

xsane crashes

The factual accuracy of this article or section is disputed.

Reason:

Should be mentioned on AUR page
This may only be relevant for the Brother DCP-150C scanner (Discuss in Talk:SANE/Scanner-specific problems)

If xsane crashes with message "=bugchk_free(ptr==(nil))@brother_modelinf.c(482)", then you need to create the link /usr/local/Brother -> /usr/share/brother.

Canon

Scanning over the network with Canon PIXMA or imageCLASS all-in-one printer/scanners

Find out your printer/scanner's IP address, and add it on a new line to /etc/sane.d/pixma.conf in the format bjnp://10.0.0.20. For imageCLASS printers you may need to use the format mfnp://10.0.0.20 instead.

Tip: Instead of an IP address, if mDNS resolution is set up, you can use the mDNS .local address. E.g. bjnp://MyPixmaPrinter.local.

Sane should now find your device. For more details refer to sane-pixma(5).

Alternatively, scangearmp2^AUR can be used for some Canon PIXMA all-in-one printer/scanners which are not detected over the network.

See SANE/Scanner-specific problems for additional information.

Epson

Driver-Backends

For Epson scanners, you can choose between two different backends: "Image Scan v3" (imagescan/utsushi) or "Image Scan! for Linux" (iscan/epkowa). You can check here for all supported imagescan/utsushi devices and here for all supported iscan/epkowa devices. What used to be the iscan package in community is out of date, and buggy. You might look at the iscan packages in the AUR. At Q3 2021, it could also be that the archived iscan, and iscan-data, packages from the archive still work reasonably for you.

Image Scan v3

If you have to use Image Scan v3-backend you can install imagescan. It should detect supported USB scanners automatically by default. If your scanner is not recognized you can directly edit the /etc/utsushi/utsushi.conf and add the following lines.

[devices]
dev1.udi     = esci:usb:<vendor id>:<product id>
dev1.name    = foo
dev1.model   = <Model Name of the scanner>

If you want to make use of a network scanner you also have to install imagescan-plugin-networkscan^AUR. Then edit /etc/utsushi/utsushi.conf and enter the ip address of your scanner to it.

[devices]
myscanner.udi    = esci:networkscan://<ip-address-here>:1865
myscanner.vendor = Epson
myscanner.model  = Model-name

When you then start Image Scan v3 by typing in the command

$ utsushi

the name of the scanner should be visible in the top left corner. If a connection problem happened, an error dialog will be shown.

Image Scan! for Linux

Install an iscan package.
Install the appropriate iscan-plugin package for your scanner (for example, iscan-plugin-gt-x820^AUR for the Epson Perfection Photo V600)
Run udevadm control --reload so that udev will recognize the device as a scanner and apply appropriate permissions.

For network (including Wi-Fi) scanners, install iscan and iscan-plugin-network^AUR, then edit /etc/sane.d/epkowa.conf and add the line:

net {IP_OF_SCANNER}

Upstream version of iscan did not support 16bpc color depth scanning. Choosing any bit depth other than 8 made iscan stop without warning, leaving the scanner stuck until restarted. To enable 16bpc scanning, iscan used to required to be patched. It could be that an old patch, found in this forum thread, will enable 16bpc depth mode.

Epson DS-6500

Usually this device works with the epsonds-backend. However, there may be an error "Error during device I / O" when scanning multiple pages. If this error occurs, the Image Scan v3 backend can be used and imagescan needs to be installed. If you want to use the network module, the scanner can be configured in the /etc/utsushi/utsushi.conf after installing imagescan-plugin-networkscan^AUR as described above.

Epson Perfection V550 Photo

Install iscan-plugin-perfection-v550^AUR

Epson Perfection 1270

For Epson Perfection 1270, you also need a firmware named esfw3e.bin. It can be obtained by installing the Windows driver.

Modify the configuration file of the snapscan backend, /etc/sane.d/snapscan.conf. Change the firmware path line with yours:

# Change to the fully qualified filename of your firmware file, if
# firmware upload is needed by the scanner
firmware /mnt/mydata/Backups/firmware/esfw3e.bin

And add the following line in the end or anywhere you like

# Epson Perfection 1270
usb 0x04b8 0x0120

You can get such code information (usb 0x04b8 0x0120) by sane-find-scanner command.

Also add such information lines to /etc/hotplug/usb/libsane.usermap to setup your privilege, like:

# Epson Perfection 1270
libusbscanner 0x0003 0x04b8 0x0120 0x0000 0x0000 0x00 0x00 0x00 0x00 0x00 0x00 0x00000000

Replug scanner, you have a working Epson Perfection 1270 now.

Note: I can scan image if I define the X and Y value, but without that error message occurs like: scanimage: sane_start: Error during device I/O, if anyone knows any other reasons, please add them to this section.

To prevent scanimage: sane_start: Error during device I/O and hangup of the scanner itself, when trying to scan with ADF (automatic document feed) enabled, I had to remove or comment out all Backends from /etc/sane.d/dll.conf and instead just add this to the file:
```
snapscan
```

If you still get the Error during device I/O messages check that the transportation lock of the scanner (on the bottom of the scanner) is open.

Epson Perfection 1670/2480/2580/3490/3590

Note: Installation instructions were only tested for Epson Perfection 3590 but should be similar to the other models. Check the instructions above and the links below and edit this wiki page if you can verify that your scanner works.

Make sure to download the correct firmware for your Epson model. You can get an overview of some models and their drivers here and here. The download links of the firmware are broken, but you can use this link as alternative instead. Make sure to change the firmware filename of the link suiting your model. If you want to download and extract the firmware sources from the official epson sites yourself you can use this guide.

As an alternative you can also install the AUR package sane-epson-perfection-firmware^AUR which will download the firmware from the official sources, extract the binary and install those to /usr/share/sane/snapscan/.

Modify the configuration file of the snapscan backend, /etc/sane.d/snapscan.conf. Change the firmware path line with yours:

# Change to the fully qualified filename of your firmware file, if
# firmware upload is needed by the scanner
firmware /usr/share/sane/snapscan/esfw52.bin

Other modifications were not needed for the Epson Perfection 3590 and might not be for other models as well. If you still have problems it can also help if you completely remove the iscan^AUR package.

EPSON WorkForce printer/scanners over the network

Install imagescan and imagescan-plugin-networkscan^AUR.

Edit the configuration file /etc/utsushi/utsushi.conf. Find the [devices] section and edit the template for dev2. Replace the IP address accordingly. You can find the IP address on your printer screen. For example,

...
dev2.udi    = esci:networkscan://192.168.1.123:1865
dev2.model  = WF-2860
dev2.vendor = EPSON
...

Meanwhile, comment out epson2 in /etc/sane.d/dll.conf as it conflicts with ImageScan.

Once this is done you can use any SANE frontend to access this scanner.

Fujitsu

Fujitsu fi series

For some of the Fujitsu fi series document scanners, the pfufs^AUR proprietary driver offers advanced functionality over the already mature SANE default driver, such as control of an optional imprinter for stamping scanned documents or requesting accurate status of the consumables from the host.

ScanSnap S300/S300M

For the operation of the ScanSnap scanners S300 and S300M a firmware file /usr/share/sane/epjitsu/300M_0C00.nal is required, which can be downloaded here or extracted from the Windows driver. The 300M_0C00.nal and 300_0C00.nal files are interchangeable; the S300 device can use the 300M_0C00.nal file and the S300M device can use the 300_0C00.nal file. The file can be renamed to fit the entry in /etc/sane.d/epjitsu.conf, or that entry can be edited to match the file name.

HP

If your HP device is supported by hplip, install the hplip package.

The latter comes with several tools:

hp-setup to add and setup the device
hp-check to check the installation of all required dependencies to successfully run (a very helpful tool)
hp-plugin is the 'HPLIP Plugin Download and Install Utility' (plugin also available from hplip-plugin^AUR).
hp-scan is the 'HPLIP Scan Utility'. If you need that tool, you will need to install python-pillow.

hp-setup requires Python Qt5 when run using the GUI (which is the default). As an alternative, you can run the CLI interface of hp-setup using -i as argument.

If the device is connected by USB, run hp-setup as root and follow the on-screen instructions.

If your device is connected on the network, use hp-setup printer_ip instead.

Alternative way to scan with network HP scanner

Find out IP address of your network HP scanner, for example 192.168.1.8
Make device URI using hp-makeuri utility:

$ hp-makeuri 192.168.1.8

hpaio:/net/DeskJet_3630_series?ip=192.168.1.8

This URI could be given to xsane or scanimage tools, for example:

$ xsane "hpaio:/net/DeskJet_3630_series?ip=192.168.1.8"
$ scanimage --device "hpaio:/net/DeskJet_3630_series?ip=10.12.129.6" --format=png --resolution 300 >scan01.png

Lexmark

For Lexmark devices printing issues, please read CUPS/Printer-specific problems#Lexmark.

Most Lexmark scanners are still (2019) not supported by SANE, and thus cannot be detected either by sane-find-scanner or by scanimage -L. Lexmark provides a non-free driver for GNU/Linux, which is supposed to support all its scanners. Nevertheless, the driver is only distributed for Debian, OpenSUSE, Fedora and RedHat, but not for Arch. Here is a way to install it.

Warning

Before following these steps, note that :

This driver is non-free (copyrighted by Lexmark)
This hasn’t been widely tested yet (but the driver is supposed to work for all Lexmark scanners)
The tree does not respect Arch standards — namely, all will be installed in /usr/local; you’ll get a /usr/lexmark/ symbolic link; and get symbolic links to the files installed in /usr/local/lexmark.
This process might generate conflicts if you’ve already installed some Lexmark drivers.

Process

Ensure Java is installed.
Download the .deb file^{[dead link 2021-11-19 ⓘ]} containing the driver and save it (eg at ~/lexmark.deb).

Option 1 : using DPKG

dpkg is the standard package-manager for Debian-based distributions. It should not be used to replace pacman unless you precisely know what you’re doing. Simply run as root

# dpkg -i lexmark.deb

Your scanner should be detected after reboot.

Option 2 : manual installation

Alternatively, if you dont want to install dpkg or wish to control exactly what is done during install, you can follow these instructions (assuming you’re working in ~). Please note that md5 sums will not be checked, which could cause security issues.

Extract the ~/lexmark.deb archive, running ar x lexmark.deb. File debian-binary can be dropped.
Extract both ~/control.tar.gz and ~/data.tar.gz archives.
data.tar.gz gives a ~/usr/ directory. As root, move ~/usr/local/lexmark to /usr/local/lexmark.
As root, run ~/control/postinst to perform install. This script will automatically set all files owners an chmod, then set some fonts, drivers and docs tricks. It will also eventually run /usr/local/lexmark/network-scan.link, creating several symbolic links in your Arch architecture.
Your scanner should be detected after reboot.

Option 3 : Using AUR package

Install the lexmark-network-scan^AUR package.

Supported devices

This process has been successfully tested for the following devices:

Lexmark MB2236 (USB only; network untested).
Lexmark MX517de (network only; USB untested).
Lexmark X204n (network only; USB untested).

It does not work fot the following:

…

To do

In order to improve Lexmark scanners support, you can:

Check whether this process works for your computer and device
Help defining the list of dependencies required for this process
Create an AUR package with this driver which installation would not mess architecture up. Namely, such a package should not need to create a /usr/lexmark symlink, and should be containerized (eg in /opt/lexmark).

Medion

If you own the USB scanner MD 9705 from Medion, you need to download a suitable firmware binary. This firmware file is in the device driver for Windows.

Find out which model you own and take note of the USB ID:

$ lsusb

Bus 006 Device 007: ID 05d8:4003 Ultima Electronics Corp. Artec E+ 48U

Download the windows driver from https://download.medion.com/downloads/treiber/scamd9705w9xxp.exe

Then enter the following commands to extract the firmware file, and copy it to the location SANE expects it:

$ unzip scamd9705w9xxp.exe Win2000/Artec48.usb
# cp Win2000/Artec48.usb /usr/share/sane/artec_eplus48u/Artec48.usb

Mustek

BearPaw 2400CU

Works with sane-gt68xx (sane-gt68xx-firmware)

Samsung

For some Samsung MFP printers you may need to edit /etc/sane.d/xerox_mfp.conf.

example entry:

#Samsung SCX-3200
usb 0x04e8 0x3441

Change the printer model as needed. You can get the idVendor and idProduct code with lsusb. See this thread.

To access the scanner over the network rather than the usb interface, add a line to /etc/sane.d/xerox_mfp.conf such as

#Samsung scx4500w wireless ip network address
tcp xx.xx.xx.xx

where xx.xx.xx.xx is the static ip address of the printer.